………………………………………………………………
PDS/ATS/issue 1 02.01
1
……………………………………………………………
A
u
to
S
e
c
A
T
S
AutoSec ATS
(Fixed Wing)
Motorised Security Revolving Door for Internal Installation
Technical Specification
Unit Dimensions
Outside Diameters:
2000 or 1830 or 1700mm
Ceiling Height:
2100mm
Cornice Height:
335mm
Overall Unit Height:
2435mm
Drive
:
Motorised
Orientation
:
Bi directional passage from both directions simultaneously.
Materials
:
Frame and Cornice:
Aluminium section powder coated
Finished Silver RAL 9006
Frame Glazing:
8.2mm 3 ply laminated safety glass
Rotor Wings:
Aluminum frame, finished Silver
RAL 9006, with 8.2mm 3 ply
laminated safety glass.
Ceiling:
Painted MDF finished White
RAL 9010
Function
:
Passage in both directions, electronically controllable.
Method of Operation
:
On receiving a signal from the access control system or push button,
the door wings will rotate through 180
O
. Receipt of further authorised
signals will continue uninterrupted rotation.
2
nd
Quadrant Entry
:
Should the authorised user not use the first available quadrant the
AutoSec will allow valid entry through the next quadrant.
Automatic Reversing
:
To enforce both security and safety by rejecting potential unauthorised
users and avoid entrapment.
Anti Tailgating
:
Prevents unauthorised passage from the opposite direction whilst a
valid passage is being made in the other direction. This is achieved
via 8N
O
sensonic sensors located in the ceiling that continuously
monitor all four door quadrants.
Anti Piggy Backing
:
Prevents two or more people attempting to pass through the same
door quadrant. For optimum security the APB system electronically
helps recognise this scenario and rejects the conditions by stopping
and reversing the door to reject the occupants.
Tamper
:
An output alarm is generated should any attempt be made to interfere
physically with the operation of the door.
(15 seconds accumulative time)
Safety
:
The door is fitted with adjustable torque sensing for the forward and
reverse directions.
Power Failure
:
The wings will rotate through 45
O
only to the crucifix position via an
inbuilt battery back up (BBU), stop and become inactive. The door will
remain in this position until power is restored.
Fire Alarm
:
The wings will rotate through 45
O
only to the crucifix position via an
inbuilt battery back up (BBU), stop and become inactive. The door will
remain in this position until power is restored.
A normally closed (NC) signal is required from others to effect this
state.
Interface
:
Momentary Zero Volt (0V) normally open (NO) signal provided by
either card reader or push button input of duration between 0.5 and
1.0 second.
The AutoSec is controlled via a microprocessor that also offers card
reader inhibits, reset, and passage confirmation as standard.
Product Description
AutoSec, the premium
security model in our
Control range, combining
high aesthetics with
material choices.
It offers the highest
possible level of
personnel control, many
security features and
ease of use.
AutoSec is an essential
door to create a secure yet
impressive entrance to
any building.
Users include
•
Government
•
Banks
•
Police HQ’s
•
Security Printers
•
Finance
•
Telecommunications
•
Information
Technology
•
Petrochemical
Product Data Sheet
ISO 9001
FM 13503
Control

ปปาณ
………………………………………………………………
PDS/ATS/issue 1 02.01
2
Installation Examples
Models Available
AutoSec Motorised Security Revolving Door Fixed Wing.
•
Model ATS1700
1700 dia. footprint.
•
Model ATS1830
1830 dia. footprint.
•
Model ATS2000
2000 dia. footprint.
Accessories and Optional Extras
Access Control Facilities
:
•
Card reader mounting box
•
Push button mounting box c/w push button
•
Simple remote override console to control both, or either, entry and exit for visitor access.
Switchable Day / Night Mode
:
•
Day mode allows free access though the door from presence sensing via a non-security PIR detector. The door will rotate on
an inout from the sensor and continue as long as the person is detected. (No security)
•
Night mode puts the door back into access control mode. (Full security)
Optional Finishes
:
•
Alternative finishes and colours
•
11.4mm 5 ply anti bandit glass
•
Tinted glass
Status Lights
:
•
LED Red Cross and Green Arrow displays
Uninterrupted Power Supply
:
•
UPS is located remotely and will have the ability to keep the AutoSec operating continuously in its normal operating mode for a
period of one hour after the mains power has failed.
Floor Mat
:
•
Dimpled rubber with a straight threshold strip between the uprights
Night Shutter
:
•
Either solid or glazed manually operated to close and lock the exposed quadrant during night time hours
Increased Cornice
:
•
The height of the cornice can be extended to fill a gap above the door.
Walkway Downlights
:
4N
O
recessed low voltage halogen downlights are positioned within the ceiling over each quadrant.
Servicing
:
Via hatches in the walkway ceiling or from overhead. The controller should always be positioned on the
secure side of the installation.
Power Supply Voltage
:
115/230 VAC 50/60Hz
Power Rating
:
1300 VA
Logic Voltage
:
24vDC
Installation Details
:
The AutoSec is delivered in kit form, which may require lifting equipment to off load.
Approximate Weight
:
600Kg

ปปาณ
………………………………………………………………
PDS/ATS/issue 1 02.01
3
Standard Site Preparation (2000mm)
Concrete Base to BS 5328:1997
specification. Base to be flat and level
to +/- 5mm over footprint area.
Dimensions to be > 2300 x 2300 x 150
deep min.
Floor Anchors to be drilled during
installation, 8mm dia x 50mm deep.
Cut out for floor bearing tray
Rubber Door Buffer
8.2 Framed Laminated Glass
Draft Excluder
8.2mm Curved 3 ply Laminated Drum Glass
Curved Aluminium Casework Extrusion
IMPORTANT
•
Any horizontal pipe or conduit runs below the AutoSec must be at least 140mm below FFL.
•
It is the customers responsibility to ensure the structural integrityand strength of the installation location.

ปปาณ
………………………………………………………………
PDS/ATS/issue 1 02.01
4
Standard Site Preparation (1830mm)
Floor Anchors to be drilled during
installation, 8mm dia x 50mm deep.
Cut out for floor bearing tray
Concrete Base to BS 5328:1997
specification. Base to be flat and level
to +/- 5mm over footprint area.
Dimensions to be > 2100 x 2100 x 150
deep min.
Rubber Door Buffer
8.2 Framed Laminated Glass
Draft Excluder
Curved Aluminium Casework Extrusion
8.2mm Curved 3 ply Laminated Drum Glass
IMPORTANT
•
Any horizontal pipe or conduit runs below the AutoSec must be at least 140mm below FFL.
•
It is the customers responsibility to ensure the structuralintegrityand strength of the installation location.

ปปาณ
………………………………………………………………
PDS/ATS/issue 1 02.01
5
Standard Site Preparation (1700mm)
Concrete Base to BS 5328:1997
specification. Base to be flat and level
to +/- 5mm over footprint area.
Dimensions to be > 2000 x 2000 x 150
deep min.
Floor Anchors to be drilled during
installation, 8mm dia x 50mm deep.
Cut out for floor bearing tray
Curved Aluminium Casework Extrusion
8.2mm Curved 3 ply Laminated Drum Glass
Draft Excluder
8.2 Framed Laminated Glass
Rubber Door Buffer
IMPORTANT
•
Any horizontal pipe or conduit runs below the AutoSec must be at least 140mm below FFL.
•
It is the customers responsibility to ensure the structural integrityand strength of the installation location.

ปปาณ
………………………………………………………………
PDS/ATS/issue 1 02.01
6
Note: In pursuit of its policy of continuous refinement and improvement, Gunnebo Mayor Ltd. reserves the right to modify design and details.
A COMPANY WITHIN THE GUNNEBO GROUP
……………………………………………………………………………………………………
United Kingdom
Gunnebo Mayor Ltd. Bellbrook Business Park, Uckfield, East Sussex, TN22 lQQ.
Tel +44 (0) 1825 761022
Fax +44 (0) 1825 763835
Gunnebo Mayor Ltd. Orient House, Newton Street, Hyde, Cheshire, SK14
4RX
Tel +44 (0) 161 882 5900 Fax +44 (0) 161 882 5910
www.gunnebomayor.com
GERMANY
Gunnebo Entrance Control GmbH
Diagonalstrasse 41, D-20537
Hamburg
Tel
+49 (0) 40 47 11 30 0
Fax
+49 (0) 40 47 11 30 79
SPAIN
Gunnebo Entrance Control
BBC, Comte d’Urgel 143, Iola 08036,
Barcelona
Tel
+34 93 452 59 56
Fax
+34 93 451 56 53
DENMARK
Gunnebo Protection A/S
Division Entrance Control
Erhvervsparken 3, DK-4621 Gadstrup
Tel
+45 46 19 14 66
Fax
+45 46 19 14 55
ITALY
Gunnebo Italdis SpA
Via A Volta 15 - IT 38015
Lavis (TN)
Tel
+39 0461 248 900
Fax
+39 0461 248 999
UNITED KINGDOM
Gunnebo Mayor Ltd
Bellbrook Business Park, Uckfield,
East Sussex, TN22 lQQ
Tel
+44 (0) 1825 761022
Fax
+44 (0) 1825 763835
HEAD OFFICE SWEDEN –Gunnebo Entrance Control AB, SE-590 93, Gunnebo.
Tel +46 (0) 490 89000, Fax +46 (0) 490 23889
FRANCE
Gunnebo Entrance Control SARL
Zone d’Activites Le Mandinet,
20 Rue des Campanules
F-77185, Lognes
Tel
+33 (0) 1 64 80 14 40
Fax
+33 (0) 1 64 80 14 39
NORWAY
Gunnebo Troax A/S
Division Entrance Control
Postboks 179, Kalbakken N-0903, Oslo
Tel.
+47 22 80 42 00
Fax
+47 22 80 42 01
USA
Gunnebo Omega Inc
5056 Commercial Circle, Suite E,
Concord, California, CA 94520
Tel
+01 925 609 6339
Fax
+019256030810
HONG KONG
Gunnebo Entrance Control
Room 2312, C.C. Wu Building,
302-308 Hennessy Road, Wanchai.
Tel
+852 2882 8337
Fax
+852 2523 7880
SWEDEN
Gunnebo Entrance Control
Box 500, Kumla Gardsvag 33F, 145 63
Norsborg
Tel
+46 (0)8 53 17 15 75
Fax
+46 (0) 8 53 18 85 39

ปปาณ